Screwking Hardware Corp.

We can help you handle any situation where a breaker is required. With the right tools you can break anything, anywhere. Lightweight - Our LH 190E is used to break brick work, frozen soil, asphalt, concrete, as well as for taming and compaction. Operator Friendly - Low vibration values , low noise levels and slim design makes this breaker a tool to use for many year to come. You've got the POWER - High power to ratio means you get more done with a smaller breaker. Ergonomic - The vibro reduction abilities of fine breaker let's you work for more than 8 hours without risking injuries.

YOHINO LIGHT CONSTRUCTION EQUIPMENT POWERED BY ROBIN ENGINES

The Concrete vibrator needle is also known as vibrating poker. It is available in various diameters,including 25mm,28mm,32mm, 35mm, 38mm,45mm,50mm,60mm,70mm and 75mm

The Concrete vibrator needle is also known as vibrating poker. It is available in various diameters,including 25mm,28mm,32mm, 35mm, 38mm,45mm,50mm,60mm,70mm and 75mm . Vibrating concrete is critical because by removing air pockets & packing the aggregate particles together, it increases the density and strength of the concrete. Tightly packed particles will result in a stronger, more durable concrete structure. Overall, vibrating concrete is a procedure that consolidates concrete by eliminating air pockets and distributes the solid particles within poured concrete properly to prevent honeycombing and improve the durability a nd quality of concrete.

The Concrete vibrator needle is also known as vibrating poker. It is available in various diameters, including 25mm,28mm,32mm, 35mm, 38mm, 45mm,50mm,60mm,70mm and 75mm

YOHINO VIBRATOR SHAFT ONLY VS32 32MM X 20FT, VS38 38MMX20FT, VS45 45MM X 20FT , VS60 60MM X 20FT

TAMPING RAMMER POWERED BY HONDA MODEL HCD80K-GX160 WEIGHT 78KG FUEL TANK CAPACITY 2.8 LITERS

transmits the drivetorque to the impellers to centrifugal pumps or to the displacement elements of rotary positive displacement pump SIZE 2''/6M MODEL MP20V

MODEL MP30V SIZE 3''/6M

CONCRETE - ASPHALT CUTTER - Q480-GX390 POWERED BY HONDA ENGINES

YOHINO ASPHALT CUTTER MODEL HCC-14-EY20 POWERED BY ORIGINAL ROBIN ENGINES CUT DEPTH (INCH) 3-4 WATR TANK CAPACITY : 20LITERS POWER OUTPUT (HP/RPM) 5.0/3600

MODEL HCC-16 - EY28 YOHINO CONCRETE ASPHALT CUTTER POWERED BY ORIGINAL ROBIN ENGINES CUT DEPTH 3-4 INCH APPLICABLE BLADE 14-16 WATER TANK CAPACITY : 25 POWER OUTPUT (HP/RPM) 7.5/3600

A power trowel, also known as a power float, is a piece of construction equipment used to apply a smooth finish to concrete slabs. There are two types power trowels, ride on power trowels and walk-behind power trowels. A ride on power trowel is used with an operator sitting on a seat and controlling the power trowel. A power trowel is an essential piece of equipment for concrete finishing jobs. These machines smooth, level and polish concrete surfaces for a quality finish. There are two kinds of power trowels — walk-behind and ride-on. Depending on the work you're doing, one type may be better suited to the job than the other.

YOHINO CONCRETE VIBRATOR MOTOR (VE3) POWER 3.0HP VOLTAGE 220V PHASE : SINGLE VIBRATION SPEED :2800rpm VIBRATOR SHAFT SIZE 6M

Note: Pre-charge pressure must be less than 2PSI below cut-in pressure. Factory Precharge: 30 P.S.I. / 2 bar Maximum Pressure: 150 P.S.I. / 10 bar Maximum Temperature: 90 Celsius

FACTORY PRECHARGE: 30P.S.I/2BAR MAXIMUM PRESSURE : 150P.S.I /10BAR MAXIMUM TEMPERATURE :90 C

FACTORY PRECHARGE 30P.S.I / 2BAR MAXIMUM PRESSURE 150P.S.I /10 BAR MAXIMUM TEMPERATURE 90 C

FACTORY PRECHARGE : 30P.S.I /20BAR MAXIMUM PRESSURE 150P.S.I /10 BAR MAXIMUM TEMPERATURE :90 C

FACTORY PRECHARGE 30 P.S.I / 2BAR MAXIMUM PRESSURE 150P.S.I /10 BAR MAXIMUM TEMPERATURE 90 C

FACTORY PRECHARGE : 30 P.S.I /2 BAR MAXIMUM PRESSURE 150P.S.I /10 BAR MAXIMUM TEMPERATURE 90 C

Stainless Steel Submersible Borehole Motor For 4" & 6" Well Casing Diameter

Stainless Steel Submersible Borehole Motor For 4" & 6" Well Casing Diameter High Quality Thrust Bearings The trust bearing is of the kingsburrY type lubricated by the internal fluid. During operation a wedge of water is drawn between the stainless steel pivot shoes and carbon disc to carry the thrust load generated by the pump. Located inside and at the bottom of the motor, the bearing is sealed away from sand and other contaminants. Sand Resistant Slinger and Lip Seals A stainless steel slinger and slinger guide are also closely fit to help prevent sand entry. Double rubber seals are installed to prevent well water and contaminants from entering the motor. High Reliable Carbon Bearing Two water lubricated carbon bearings are used as guide bearings. These have extremely large surface area and result in extra alignment support-less whipping and acts as a steady bushing. Water-Filled Design The motor lubrication is provided by the internal cooling water consistings of a water, anti-freeze and anti-rust mixture good to 30°C (-22°F). This mixture is installed at the factory. Two water plugs are located near of the top of the motor and are used by the installer to check the water level or to the top off needed before installation. Complete Corrosion and Water-Tight Protection All main motor components are made of stainless steel: including the can housing (water tight type motors have baked epoxy coated steel housing), Shaft and bolts. All other motor parts are coated with the baked epoxy coating.

This depends upon the depth of the borehole to ground level and then the distance from the ground level to the final end point e.g. where the water tank is sited. The further the distance, the higher the pressure requirements of the borehole pump to prevent the water from trickling out. Submersible borehole pumps are a type of submersible pump. They are centrifugal pumps driven by a submersible motor. As they usually draw in the fluid directly without a suction line, they must constantly be submerged in the fluid handled. Starter borehole pumps can run for up to 24 hours. However, your everyday borehole pump will run between 6 & 8 hours. It is not good for your borehole pump to run continuously. If you run electrical pumps continuously, your utility bill will skyrocket.

The diameter of the borehole is usually around 120 to 160 mm, and its depth can reach up to 300 meters, although depth ​​of about 40 meters is more common. Your pump and its control system must also meet the specific conditions as well as the high demands on reliability. This depends upon the depth of the borehole to ground level and then the distance from the ground level to the final end point e.g. where the water tank is sited. The further the distance, the higher the pressure requirements of the borehole pump to prevent the water from trickling out. Submersible borehole pumps are a type of submersible pump . They are centrifugal pumps driven by a submersible motor. As they usually draw in the fluid directly without a suction line, they must constantly be submerged in the fluid handled.

The diameter of the borehole is usually around 120 to 160 mm, and its depth can reach up to 300 meters, although depth ​​of about 40 meters is more common. Your pump and its control system must also meet the specific conditions as well as the high demands on reliability. This depends upon the depth of the borehole to ground level and then the distance from the ground level to the final end point e.g. where the water tank is sited. The further the distance, the higher the pressure requirements of the borehole pump to prevent the water from trickling out. Submersible borehole pumps are a type of submersible pump. They are centrifugal pumps driven by a submersible motor. As they usually draw in the fluid directly without a suction line, they must constantly be submerged in the fluid handled.

Stainless Steel Submersible Borehole Motor For 4" & 6" Well Casing Diameter High Quality Thrust Bearings The trust bearing is of the kingsburry type lubricated by the internal fluid. During operation a wedge of water is drawn between the stainless steel pivot shoes and carbon disc to carry the thrust load generated by the pump. Located inside and at the bottom of the motor, the bearing is sealed away from sand and other contaminants. Sand Resistant Slinger and Lip Seals A stainless steel slinger and slinger guide are also closely fit to help prevent sand entry. Double rubber seals are installed to prevent well water and contaminants from entering the motor. High Reliable Carbon Bearing Two water lubricated carbon bearings are used as guide bearings. These have extremely large surface area and result in extra alignment support-less whipping and acts as a steady bushing. Water-Filled Design The motor lubrication is provided by t he internal cooling water consistings of a water, anti-freeze and anti-rust mixture good to 30 °C (-22°F). This mixture is installed at the factory. Two water plugs are located near of the top of the motor and are used by the installer to check the water level or to the top off needed before installation. Complete Corrosion and Water-Tight Protection All main motor components are made of stainless steel: including the can housing (water tight type motors have baked epoxy coated steel housing), Shaft and bolts. All other motor parts are coated with the baked epoxy coating.

Stainless Steel Submersible Borehole Motor For 4" & 6" Well Casing Diameter High Quality Thrust Bearings The trust bearing is of the kingsburry type lubricated by the internal fluid. During operation a wedge of water is drawn between the stainless steel pivot shoes and carbon disc to carry the thrust load generated by the pump. Located inside and at the bottom of the motor, the bearing is sealed away from sand and other contaminants. Sand Resistant Slinger and Lip Seals A stainless steel slinger and slinger guide are also closely fit to help prevent sand entry. Double rubber seals are installed to prevent wel l water and contaminants from entering the motor. High Reliable Carbon Bearing Two water lubricated carbon bearings are used as guide bearings. These have extremely large surface area and result in extra alignment support-less whipping and acts as a steady bushing. Water-Filled Design The motor lubrication is provided by the internal cooling water consistings of a water, anti-freeze and anti-rust mixture good to 30°C (-22°F). This mixture is installed at the factory. Two water plugs are located near of the of the motor and are used by the installer to check the water level or to the top off needed before installation. Complete Corrosion and Water-Tight Protection All main motor components are made of stainless steel : including the can housing (water tight type motors have baked epoxy coated steel housing), Shaft and bolts. All other motor parts are coated with the baked epoxy coating.

Stainless Steel Submersible Borehole Motor For 4" & 6" Well Casing Diameter High Quality Thrust Bearings The trust bearing is of the kingsburry type lubricated by the internal fluid. During operation a wedge of water is drawn between the stainless steel pivot shoes and carbon disc to carry the thrust load generated by the pump. Located inside and at the bottom of the motor, the bearing is sealed away from sand and other contaminants. Sand Resistant Slinger and Lip Seals A stainless steel slinger and slinger guide are also closely fit to help prevent sand entry. Double rubber seals are installed to prevent well water and contaminants from entering the motor. High Reliable Carbon Bearing Two water lubricated carbon bearings are used as guide bearings. These have extremely large surface area and result in extra alignment support- less whipping and acts as a steady bushing. Water-Filled Design The motor lubrication is provided by the internal cooling water consistings of a water, anti-freeze and anti-rust mixture good to 30°C (-22°F). This mixture is installed at the factory. Two water plugs are located near of the top of the motor and are used by the installer to check the water level or to the top off needed before installation. Complete Corrosion and Water-Tight Protection All main motor components are made of stainless steel: including the can housing (water tight type motors have baked epoxy coated steel housing), Shaft and bolts. All other motor parts are coated with the baked epoxy coating.

Stainless Steel Submersible Borehole Motor For 4" & 6" Well Casing Diameter High Quality Thrust Bearings The trust bearing is of the kingsburry type lubricated by the internal fluid. During operation a wedge of water is drawn between the stainless steel pivot shoes and carbon disc to carry the thrust load generated by the pump. Located inside and at the bottom of the motor, the bearing is sealed away from sand and other contaminants. Sand Resistant Slinger and Lip Seals A stainless steel slinger and slinger guide are also closely fit to help prevent sand entry. Double rubber seals are installed to prevent well water and contaminants from entering the motor. High Reliable Carbon Bearing Two water lubricated carbon bearings are used as guide bearings. These have extremely large surface area and result in extra alignment support-less whipping and acts as a steady bushing. Water-Filled Design The motor lubrication is provided by the internal cooling water consistings of a water, anti-freeze and anti-rust mixture good to 30°C (-22°F). This mixture is installed at the factory. Two water plugs are located near of the top of the motor and are used by the installer to check the water level or to the top off needed before installation. Complete Corrosion and Water-Tight Protection All main motor components are made of stainless steel: including the can housing (water tight type motors have baked epoxy coated steel housing), Shaft and bolts. All other motor parts are coated with the baked epoxy coating.

to control the various mechanical functions of industrial equipment or machinery