Search
You have no items in your shopping cart.
Screwking Hardware Corp.
Flashlight,Headsup Lite, LED Headlight,4.5V, 7.1cm, With 3 AAA Alkaline,Black
₱2,570.00
They are completely different ; impact drivers provide torsional (rotational) impulses which act to drive the fastener clockwise as the screw advances into the material, percussion (hammer drill) provides linear impulses along the axis of the bit that act to micro-shatter the substrate (typically masonry) being drilled . A hammer drill works at a lower stroke rate, but with significantly greater impact energy than a percussion drill. This enables work to be completed more quickly. Hammer drilling in concrete requires less force than percussion drilling. An impact drill uses lateral percussion (from the side, in a circular motion). Once the drill senses that torque is needed , the drill uses impact to twist the screw into the surface. In short, an impact drill is used for driving screws and bolts that require a higher torque. Impact drivers produce lots of rotational force, capable of driving the largest wood screws in seconds. Internal mechanisms allow impact drivers to produce more torque than drills, and in quick bursts. These bursts or “impacts” happen up to 50 times a second, giving impact drivers their name. Can you use an impact driver to drill into concrete? If you drill holes that are less than 1/4 inch, an impact driver can help drill through concrete and brick. These tools have a massive amount of torque. However, they are not built to be used like hammer or regular drills. Percussion drilling is the perfect choice if you need to execute drilling in hard soils. Hard soil has layers of rubble or stones and percussion drilling can effectively drill through it. It is suitable for research on soil pollution, grain size distribution, general soil classification, and profile description. Percussion drilling is a drilling method in which a heavy hammering or cutting bit is attached to a cable and inserted into the borehole. The heavy bit or hammer is repeatedly lifted and dropped, thus boring through the earth. The hammer is made of hardened steel with carbide on the chisel -shaped bit.
₱71,250.00 ₱57,000.00
They are completely different ; impact drivers provide torsional (rotational) impulses which act to drive the fastener clockwise as the screw advances into the material, percussion (hammer drill) provides linear impulses along the axis of the bit that act to micro-shatter the substrate (typically masonry) being drilled . A hammer drill works at a lower stroke rate, but with significantly greater impact energy than a percussion drill. This enables work to be completed more quickly. Hammer drilling in concrete requires less force than percussion drilling. An impact drill uses lateral percussion (from the side, in a circular motion). Once the drill senses that torque is needed , the drill uses impact to twist the screw into the surface. In short, an impact drill is used for driving screws and bolts that require a higher torque. Impact drivers produce lots of rotational force, capable of driving the largest wood screws in seconds. Internal mechanisms allow impact drivers to produce more torque than drills, and in quick bursts. These bursts or “impacts” happen up to 50 times a second, giving impact drivers their name. Can you use an impact driver to drill into concrete? If you drill holes that are less than 1/4 inch, an impact driver can help drill through concrete and brick. These tools have a massive amount of torque. However, they are not built to be used like hammer or regular drills. Percussion drilling is the perfect choice if you need to execute drilling in hard soils. Hard soil has layers of rubble or stones and percussion drilling can effectively drill through it. It is suitable for research on soil pollution, grain size distribution, general soil classification, and profile description. Percussion drilling is a drilling method in which a heavy hammering or cutting bit is attached to a cable and inserted into the borehole. The heavy bit or hammer is repeatedly lifted and dropped, thus boring through the earth. The hammer is made of hardened steel with carbide on the chisel -shaped bit.
₱13,750.00 ₱11,000.00
What is a demolition hammer? The demolition hammer is one of the power tools specifically designed for the demolition of the structure. It is also known as stomping hammers. Demolition hammer tools are strong enough to break down various materials such as wooden walls, concrete surfaces and tile flooring. Jackhammers, also known as demolition hammers or concrete breakers, are the primary tool in the breaking of old or non-standard structures and are a must-have for construction and renovation projects that often involve tearing down concrete slabs, tiles, or brick walls. A hammer drill, also known as a percussion drill or impact drill, is a power tool used chiefly for drilling in hard materials. It is a type of rotary drill with an impact mechanism that generates a hammering motion. Hammers are powerful enough to break up blocks of brick and concrete with ease. Our breaker hammers work with many Cat machines, meaning you can quickly transform your existing equipment into a robust demolition tool just by renting a breaker hammer. It is perfect for demolition, trenching, chipping, breaking holes in concrete, block, brick, tile stucco, housing foundation removal, concrete slab , oil chimney and much more! SDS is short for Slotted Drive Shaft or Slotted Drive System. These drills are typically used for heavy-duty drilling into materials such as brick, stone, oncrete and other types of masonry. Unlike regular drills, they have a SDS is short for Slotted Drive Shaft or Slotted Drive System. These drills are typically u sed for heavy-duty drilling into materials such as brick, stone, concrete and other types of masonry. Unlike regular drills, they have a unique design that provides a high level of power during drilling.
₱56,250.00 ₱45,000.00
Drill bit sizes are written as irreducible fractions . So, instead of 78/64 inch, or 1 14/64 inch, the size is noted as 1 7/32 inch. Below is a cart providing the decimal-fraction equivalents that are most relevant to fractional-inch drill bit sizes (that is, 0 to 1 by 64ths). (Decimal places for . If you know the size of the screw, you can locate the size of the drill bit by looking at the opposite end from the sharp point of the bit. It's likely engraved there. Standard metric sizes are defined in ISO 2936:2014 "Assembly tools for screws and nuts —Hexagon socket screw keys", also known as DIN 911. The full set of defined sizes are: 0.7 mm, 0.9 mm, 1.3 mm. 1.5 to 5 mm in 0.5 mm increments. They're great for being able to be quickly swapped out if you an adapter, and even without an adapter that hex shank is a lot easier for your drill chuck to grab onto when using very small bits like 1/16” & smaller. You'll see a list of numbers from to 10 or 20. These are used to set the clutch to deliver a torque range. The higher the number on the collar, the higher the torque and the larger the fastener that can be driven. To adjust your clutch, align the arrow to a lower setting and start driving a screw. Take a loose screw and compare it to the size of the bit you need to use, using the screw's core rather than its flute. A bit that is very slightly smaller than the screw will ensure a proper fit. Choosing a bit that is too small means that the screw will get stuck so take care to choose carefully. In hex, four digits of a binary number can be represented by a single hex digit. Dividing a binary number into 4-bit sets means that each set can have a possible value of between 0000 and 1111, allowing 16 number combinations from 0 to 15. With the base value as 16, the maximum value of a digit is 15.
₱5,100.00 ₱4,080.00
Drill bit sizes are written as irreducible fractions . So, instead of 78/64 inch, or 1 14/64 inch, the size is noted as 1 7/32 inch. Below is a cart providing the decimal-fraction equivalents that are most relevant to fractional-inch drill bit sizes (that is, 0 to 1 by 64ths). (Decimal places for . If you know the size of the screw, you can locate the size of the drill bit by looking at the opposite end from the sharp point of the bit. It's likely engraved there. Standard metric sizes are defined in ISO 2936:2014 "Assembly tools for screws and nuts —Hexagon socket screw keys", also known as DIN 911. The full set of defined sizes are: 0.7 mm, 0.9 mm, 1.3 mm. 1.5 to 5 mm in 0.5 mm increments. They're great for being able to be quickly swapped out if you an adapter, and even without an adapter that hex shank is a lot easier for your drill chuck to grab onto when using very small bits like 1/16” & smaller. You'll see a list of numbers from to 10 or 20. These are used to set the clutch to deliver a torque range. The higher the number on the collar, the higher the torque and the larger the fastener that can be driven. To adjust your clutch, align the arrow to a lower setting and start driving a screw. Take a loose screw and compare it to the size of the bit you need to use, using the screw's core rather than its flute. A bit that is very slightly smaller than the screw will ensure a proper fit. Choosing a bit that is too small means that the screw will get stuck so take care to choose carefully. In hex, four digits of a binary number can be represented by a single hex digit. Dividing a binary number into 4-bit sets means that each set can have a possible value of between 0000 and 1111, allowing 16 number combinations from 0 to 15. With the base value as 16, the maximum value of a digit is 15.
₱6,300.00 ₱5,040.00
Drill bit sizes are written as irreducible fractions . So, instead of 78/64 inch, or 1 14/64 inch, the size is noted as 1 7/32 inch. Below is a cart providing the decimal-fraction equivalents that are most relevant to fractional-inch drill bit sizes (that is, 0 to 1 by 64ths). (Decimal places for . If you know the size of the screw, you can locate the size of the drill bit by looking at the opposite end from the sharp point of the bit. It's likely engraved there. Standard metric sizes are defined in ISO 2936:2014 "Assembly tools for screws and nuts —Hexagon socket screw keys", also known as DIN 911. The full set of defined sizes are: 0.7 mm, 0.9 mm, 1.3 mm. 1.5 to 5 mm in 0.5 mm increments. They're great for being able to be quickly swapped out if you an adapter, and even without an adapter that hex shank is a lot easier for your drill chuck to grab onto when using very small bits like 1/16” & smaller. You'll see a list of numbers from to 10 or 20. These are used to set the clutch to deliver a torque range. The higher the number on the collar, the higher the torque and the larger the fastener that can be driven. To adjust your clutch, align the arrow to a lower setting and start driving a screw. Take a loose screw and compare it to the size of the bit you need to use, using the screw's core rather than its flute. A bit that is very slightly smaller than the screw will ensure a proper fit. Choosing a bit that is too small means that the screw will get stuck so take care to choose carefully. In hex, four digits of a binary number can be represented by a single hex digit. Dividing a binary number into 4-bit sets means that each set can have a possible value of between 0000 and 1111, allowing 16 number combinations from 0 to 15. With the base value as 16, the maximum value of a digit is 15.
₱5,400.00 ₱4,320.00
Drill bit sizes are written as irreducible fractions . So, instead of 78/64 inch, or 1 14/64 inch, the size is noted as 1 7/32 inch. Below is a cart providing the decimal-fraction equivalents that are most relevant to fractional-inch drill bit sizes (that is, 0 to 1 by 64ths). (Decimal places for . If you know the size of the screw, you can locate the size of the drill bit by looking at the opposite end from the sharp point of the bit. It's likely engraved there. Standard metric sizes are defined in ISO 2936:2014 "Assembly tools for screws and nuts —Hexagon socket screw keys", also known as DIN 911. The full set of defined sizes are: 0.7 mm, 0.9 mm, 1.3 mm. 1.5 to 5 mm in 0.5 mm increments. They're great for being able to be quickly swapped out if you an adapter, and even without an adapter that hex shank is a lot easier for your drill chuck to grab onto when using very small bits like 1/16” & smaller. You'll see a list of numbers from to 10 or 20. These are used to set the clutch to deliver a torque range. The higher the number on the collar, the higher the torque and the larger the fastener that can be driven. To adjust your clutch, align the arrow to a lower setting and start driving a screw. Take a loose screw and compare it to the size of the bit you need to use, using the screw's core rather than its flute. A bit that is very slightly smaller than the screw will ensure a proper fit. Choosing a bit that is too small means that the screw will get stuck so take care to choose carefully. In hex, four digits of a binary number can be represented by a single hex digit. Dividing a binary number into 4-bit sets means that each set can have a possible value of between 0000 and 1111, allowing 16 number combinations from 0 to 15. With the base value as 16, the maximum value of a digit is 15.
₱6,600.00 ₱5,280.00
2M Size Dimmer Switch Philips 300W Origami Style
₱795.00
The majority of angle grinders have a fixed speed. Most 4-½-inch models run at 10,000 or 11,000 rpm. The said, 7-inch and 9-inch models run between 5,000 and 8,000 rpm. A few angle grinders have variable speed and can run slow enough for polishing or buffing. Grinder's come in lots of different disc sizes, but the most common sizes are 115mm (4 ½”) and 230mm (9”). You can purchase different discs/heads/ wheels depending on the task you want to complete - just make sure they're the right size for your grinder! 4' (100mm) angle grinders, as the name suggests, accept grinding discs up to 100mm in size. These grinders are relatively small in size, and are suitable for smaller jobs. The size of disc that the grinder can accept dictates the depth of cut that the grinder can achieve. Complete various grinding applications and get fast material removal with the 9-in. 4HP Angle Grinder. Featuring a high-powered motor with overload protection, this grinder delivers 6,500 rpm for tough jobs. The GA9060 weighs only 5.5 Kg and is built with comfort and ergonomic features for extended use. The grinder features an ergonomic rubberised handle with trigger switch, and the gear housing can be positioned every 90 degrees for operator convenience.
₱125,750.00 ₱100,600.00
utility knives snaps off in segments to remove worn cutting edges and expose sharp ones. Their sliding lever moves the blade strip into and out of the knife handle to retract and extend the cutting edge. A utility knife is generally six inches long and works well for slicing fruit, tender pieces of meat, or sandwiches. As the “knife of all trades,” it's a handy go-to for the everyday chef. “Snap-off blades have so many advantages: they allow for longer blade exposure; they're convenient, safer, versatile and always ready to use – and you'll have quick access to fresh, always-sharp blades. OLFA® STAINLESS STEEL™ blades are sharper than most other snap-off blades in the world, and rust-proof. This makes them perfectly suitable when things can get a little wet or moist. Utility knives are used to cut and trim a variety of building materials including: drywall, felt paper, wallpaper, rope & twine, plastic sheet material, fiberglass insulation and more. They can be divided into 3 general categories, Retractable Blade, Fixed Blade and Snap-off Blade. Utility knives usually only expose about 3/4-inch of the blade, so you have a limited cutting depth. Snap-offs retract around a couple of inches if you need to make a deeper cut in something like foam insulation.
₱905.00 ₱724.00
Stainless Steel Allen Socket Head Cap Screw
₱9.50
Min: ₱0.00 Max: ₱2,244,125.00
₱0 ₱2244125